Alternative Technologies for Ethernet
From Computing and Software Wiki
| Line 70: | Line 70: | ||
[http://en.wikipedia.org/wiki/Ethernet_crossover_cable#Crossover_cable_pinouts "Taken From"] | [http://en.wikipedia.org/wiki/Ethernet_crossover_cable#Crossover_cable_pinouts "Taken From"] | ||
| + | [[Image:cat5.jpg|thumb|180px|right| | ||
| + | '''Standard Category 5 Cable''']] | ||
=== Cat5/6 Cables === | === Cat5/6 Cables === | ||
The most typical means of ethernet today is by using category 5 patch cables (utilizing twisted pair copper wiring). It is extremely cheap to produce, making it the most readily available solution to setting up small scale networks. However the tradeoff for such versatility is a fairly low maximum transfer rate, usually reaching only around 150mb/s, and with many high bandwidth applications today requiring much more, alternative solutions are a necessity. | The most typical means of ethernet today is by using category 5 patch cables (utilizing twisted pair copper wiring). It is extremely cheap to produce, making it the most readily available solution to setting up small scale networks. However the tradeoff for such versatility is a fairly low maximum transfer rate, usually reaching only around 150mb/s, and with many high bandwidth applications today requiring much more, alternative solutions are a necessity. | ||
Revision as of 20:02, 8 April 2008
With its introduction in the early 1980s, Ethernet has been the predominant solution to local area networking all over the world. But with advances in technology and other countries exploring new options, it is only just now that many new alternatives to the standard approach of using the common twisted pair cables, are emerging. These kind of networks can be found anywhere, from a network in your house, to the network connecting all the computers in a school or business. However larger networks that do not consist of simple point to point connection would require many more hubs to bridge the connections between networked machines.
Contents |
Alternative Technologies for Ethernet
- Fiber Optic Cable
- Crossover Cable
- Faster Ethernet with Category 5/6 Cable
Use of Fiber Optic Cables
The basic premise behind fiber optic networking, is to send pulses of light through an optical fiber (A long wire of usually plastic or glass, that acts to guide light across its entire length)The obvious benefit to using light over electrical signals is speed, light can move a lot faster than any other form of signal. However the use of optical fiber cables does have many disadvantages, and is not necessarily the best option when it comes to ethernet. First and foremost, installing a Fiber Optic system can be extremely expensive and time consuming. Also, Fiber Optics are primarily most effective when being used over a large distance (ie. Cross continental) for privatized, high bandwidth applications. Due to these limitations, although Fiber Optics are better in some cases, as of now it is still much more cost, and resource, efficient to use other means of networking on a smaller scale.
Crossover Cables
Crossover cables were a means to avoid the need for a switch or hub/router. Acting and being almost identical to standard ethernet twisted pair cables, the only difference being that on one end of the cable the wire pairs are swapped in position 2 and 3. This allows for crossover cables to be used to directly connect two machines together without the need for any switch in between. Recently, however, crossover cables are quickly becoming obselete. With the release of network interface cards that are capable of doing the switch internally takes away the need for crossover cables, and standard twisted pair cables can be used to achieve the same result.
Standard Crossover cable pinouts
| Pin | Connection 1 pair | Connection 2 pair | Connection 1 | Connection 2 | |
|---|---|---|---|---|---|
| 1 | 3 | 2 | white/green stripe | white/orange stripe | |
| 2 | 3 | 2 | green solid | orange solid | |
| 3 | 2 | 3 | white/orange stripe | white/green stripe | |
| 4 | 1 | 1 | blue solid | blue solid | |
| 5 | 1 | 1 | white/blue stripe | white/blue stripe | |
| 6 | 2 | 3 | orange solid | green solid | |
| 7 | 4 | 4 | white/brown stripe | white/brown stripe | |
| 8 | 4 | 4 | brown solid | brown solid |
Cat5/6 Cables
The most typical means of ethernet today is by using category 5 patch cables (utilizing twisted pair copper wiring). It is extremely cheap to produce, making it the most readily available solution to setting up small scale networks. However the tradeoff for such versatility is a fairly low maximum transfer rate, usually reaching only around 150mb/s, and with many high bandwidth applications today requiring much more, alternative solutions are a necessity.
References
"Fiber Optic Communication"
"Ethernet Crossover Cable"
See Also
External Links
